DAS NX-148E LCD Codepad Bedienungsanleitung

HILLS® Series LCD Code Pad User Manual

CANCEL / ABORT FEATURE (Optional, if programmed) The cancel light will flash during an abort delay time. If a code is entered followed by the [CANCE

Procedure #2 If you do not know the number of the zone you wish to bypass, use the following steps: Step 1 Press r • The description for

Auxiliary Key - If programmed, you can activate the auxiliary alarm by pressing the Emergency Activation [Auxiliary] key for two seconds. If your syst

VIEW ZONE STATUS Step 1 Press r • . The LCD Screen will display the zone status. Step 2 Use the up and down scroll keys to browse through the

DISPLAY TEST FUNCTION This function will perform a test of the LCD display. No alarms or reports will be sent. Step 1 Press r 4 5 . Th

CHANGING USER CODES Step 1 Press r 5 . The LCD Screen will prompt for a code. Step 2 Enter [master code]. The LCD Screen will prompt for

PROMPT Outputs used? » DO NOT CHANGE THIS SEGMENT! Open / Close Rprt? Bypass enable? Arm / Disarm? (These are for use by a professional insta

READING THE EVENT LOG The control panel has an event log that can be retrieved using a master code. This log contains a listing of the events along

SETTING THE SYSTEM CLOCK Step 1 Enter r 9 7 . The LCD Screen will prompt for a code. Step 2 Enter [master code]. The time and date

IV. PARTITIONED SYSTEMS OPERATION This system is “ is not “ partitioned. If your system is multi-partitioned and the keypad resides in one

THIS MANUAL IS FURNISHED TO HELP YOU UNDERSTAND YOUR SECURITY SYSTEM AND BECOME PROFICIENT IN ITS OPERATION. ALL USERS OF YOUR SECURITY SYSTEM SHOULD

DISPLAYS IN THE PARTITIONING MASTER MODE  ARMED and READY STATUS The LCD screen will display the Armed and Ready status of ALL eight (8) partitions i

 To disarm all of these areas, press • .  To arm all of these areas, press – .  To toggle a single area between the armed and disarmed condi

V. KEYPAD CONTROL TONES (BEEPS) A sounder is built into the keypad and may sound for any of the following reasons:  Beeps for all key presses. 

VI. SERVICE DISPLAY The following message will be displayed periodically if the security system requires service. Call your service provider promptl

Expansion Box tamper A box containing an expansion device has been opened. Expansion Low Battery An expansion power supply has a low battery. Expansio

VII. APPENDIX A - EVENT LOG NOTE: Your system may not have all of the features listed in this table. DISPLAY DESCRIPTION TXlobat Transmitter Low B

DISPLAY DESCRIPTION Cancel Cancel System is disarmed and the Cancel button was pressed within 5 minutes of an alarm. Gnd Flt Ground Fault A short t

VIII. EMERGENCY EVACUATION PLANS An emergency evacuation plan should be established for an actual fire alarm condition. For example, the following

Programmed Phone Number 1: Programmed Phone Number 2: Programmed Phone Number 3: ZONE LIST ENTRY / EXIT 24 STAY MODE 24

TABLE OF CONTENTS I. GLOSSARY OF TERMS ...3 II. UNDERSTANDING THE LIGHTS ...

Hills LCD Keypad 2

I. GLOSSARY OF TERMS Abort Delay: An option that allows a delay in reporting to the central station. Authority Level: The level of access an indiv

II. UNDERSTANDING THE LIGHTS Armed Light The armed light is “on” when the system is armed. The armed light is “off” when it is disarmed. The armed

III. KEYPAD FUNCTIONS ARMING YOUR SYSTEM IN THE “AWAY” MODE AWAY is utilized when the user is going away from the premise and wants the interior prot

ARMING YOUR SYSTEM IN THE “STAY” MODE STAY is utilized when the user is inside the premise and wants protection around the perimeter. The steps to ar

USING THE QUICK ARM The Quick Arm feature may be used if it is enabled. Quick Arm will allow the user to arm the security system in the AWAY mode by